Read Only Parameters (EU) | |||||
---|---|---|---|---|---|
Hex | Decimal | Coil | Name | Description | Display |
02CC | 716 | 31001 | Process value (PV) | -1999 to 9999 (within input scale) | |
08CA | 2250 | 31002 | Currently used set value (SV) | -1999 to 9999 (within set Value Limit) | |
FA02 | -1534 | 31003 | Currently used deviation (DV) | -1999 to 9999 (-100 to 100% value of input scale) | |
283C | 10300 | 31004 | MV (output 1) | -300 to 10300 (-3.00 to 103.00%) | OUT1 |
0000 | 0 | 31007 | Alarm status | (refer to Section 7.4.) |
Read/Write Parameters (EU) | |||||
---|---|---|---|---|---|
Hex | Decimal | Coil | Name | Description | Display |
0000 | 0 | 41002 | PID/FUZZY/SELF selection | 0:PID control 1:FUZZYcontrol 2:SELF tuning control | CTrL |
08CA | 2250 | 41003 | SV value set on face panel | -1999 to 9999 (within set value limits) | |
0000 | 0 | 41004 | Control RUN/standby | 0: Invalidate standby (RUN) 1:Validate standby | STby |
0000 | 0 | 41005 | Auto tuning command | 0: Autotuning disabled 1: Standard type AT 2: Low PV Type AT | AT |
0025 | 37 | 41006 | P | 0 to 9999 (0.0 to 999.9%) | P |
035A | 858 | 41007 | I | 0 to 32000 (0 to 3200.0) sec | i |
00A5 | 165 | 41008 | D | 0 to 9999 (0.0 to 999.9) sec | D |
000A | 10 | 41009 | Hysteresis range at two-position control | 0 to 9999 (0 to 50% value of input scale) | HyS |
000A | 10 | 41010 | COOL | 0 to 1000 (0.0 to 100.0) | CooL |
0000 | 0 | 41011 | Dead band | -5000 to 5000 (-50.00 to +50.00) | db |
02EE | 750 | 41012 | Anti-reset windup | -1999 to 9999 (0 10 100% value of input scale) | Ar |
0000 | 0 | 41013 | Output convergence value | -10000 to 10000 (-100.00 to 100.00%) | bAL |
0000 | 0 | 41014 | PV shift | -1999 to 9999 (-10 to 10% value of input scale) | PVOF |
0000 | 0 | 41015 | SV offset | -1999 to 9999 (-50 to 50% value of input scale) | SVOF |
0003 | 3 | 41016 | Input type code | 0 to 16 | P-n2 |
0001 | 1 | 41017 | Temperature unit | 0:degC 1:degF | P-F |
0140 | 320 | 41018 | Input scale lower limit | -1999 to 9999 | P-SL |
1D60 | 7520 | 41019 | Input scale upper limit | P-SU | |
0001 | 1 | 41020 | Decimal point place | 0 to 2 | P-dP |
000A | 10 | 41022 | Input filter time constant | 0 to 9000 (0.0 to 900.0 sec) | P-dF |
0001 | 1 | 41023 | RCJ yes/no | 0: Disable RCJ 1: Enable RCJ (perform reference cold junction compensation) | rCJ |
000B | 11 | 41041 | Alarm 1 type | 0 to 34 | ALM1 |
0018 | 24 | 41042 | Alarm 2 type | ALM2 | |
0005 | 5 | 41044 | Alarm 1 set value or alarm 1 lower limit set value | -1999 to 9999 For absolute value alarm: 0 to 100.00% value of input scale For deviation alarm: -100 to 100% value of input scale | AL1 or A1-L |
0B54 | 2900 | 41045 | Alarm 2 set value or alarm 2 lower limit set value | AL2 or A2-L | |
0000 | 0 | 41047 | Alarm 1 upper limit set value | A1-H | |
0FA0 | 4000 | 41048 | Alarm 2 upper limit set value | A2-H | |
0000 | 0 | 41050 | Alarm 1 hysteresis | 0 to 9999 (0 to 50% value of input scale) | A1hy |
0000 | 0 | 41051 | Alarm 2 hysteresis | A2hy | |
0000 | 0 | 41053 | Alarm 1 ON-delay set value | 0 to 9999 (0 to 9999 sec) | dLy1 |
0000 | 0 | 41054 | Alarm 2 ON-delay set value | dLy2 | |
0BB8 | 3000 | 41057 | Set Value 2 Used with DI switch | -1999 to 9999 | Sv-1 |
008C | 140 | 41085 | PV stable range | -1999 to 9999 (within input scale) | SLFb |
0001 | 1 | 41089 | Output proportional cycle (output 1) | 0: Current output type,1 to 150(1 to 150 sec):Relay, SSR drive output type | TC |